Any ideas as to what I’m doing wrong?

This sphere has a ridge on it, and I’ve had miniatures come out with the base to be slightly offset giving a bit of a ridge.

I’m using a Halot One, lychee Slicer, and Anycubic Water Wash resin.

  • NaibofTabr
    link
    fedilink
    English
    67 months ago

    Are you printing this near the center of your print bed?

    I suspect that the object is not fully peeling off the FEP film, but just pulling it up for some of the layers. When it eventually releases the print continues.

    I think you should lift higher, maybe double it to 10mm, to make sure that it completely separates from the film every layer.

    • @thantik@lemmy.world
      link
      fedilink
      English
      4
      edit-2
      7 months ago

      Given my experience, this is what I would say too. Not separating from the FEP. Very specifically, I notice he’s printing a sphere. These are known to cause suction-cupping, and generally the symptom of said suction cupping is…this.

      • @KairuByte@lemmy.dbzer0.com
        link
        fedilink
        English
        27 months ago

        Suction cupping causes the print to rip from the build plate/supports, it wouldn’t cause this. Especially since it continues along as if a few layers were cut out of the file, which just isn’t something caused by suction cupping. It would essentially need to be stuck to the FEP to such an extreme degree that the stepper motor is unable to move.

        • @thantik@lemmy.world
          link
          fedilink
          English
          2
          edit-2
          7 months ago

          Suction cupping causes the print to rip from the build plate/supports

          It can cause both, actually. And it continues along, because it eventually gets up high enough in layers that the additional lift manages to break the suction effect. Finally allowing the resin to drop out of the top of the model and for it to cease happening. If the FEP film isn’t tight enough, or has loosened up due to wear, it absolutely can follow the print upwards without disconnecting for a few layers, without pulling the print off of the build plate.

          I, quite literally, run one of the few professional shop for repairing FDM and Resin based printers in the USA and have 12 years of experience in the field; engineering systems, designing products, and even had a few successful 3D printer kickstarters. Sure - without looking at it happen in person, I could be missing something here, but I highly doubt it.

          Additionally, I’ve seen this exact failure mode on the peopoly Phenom due to its excessively large FEP vat, as mentioned - due to suction cupping. The model never separated from the build plate. The motor doesn’t have to cease moving, you merely need too little lift, and a loose FEP film.

          • @Tarnaq@lemmy.worldOP
            link
            fedilink
            English
            17 months ago

            Suction cupping could be a possibility on the sphere, it does not explain why I had ridges on miniature prints.

            • @thantik@lemmy.world
              link
              fedilink
              English
              1
              edit-2
              7 months ago

              A loose FEP film can explain the ridges, which would exacerbate the ability for a part to suction cup like that. I mentioned that, as they’re interrelated.

          • @KairuByte@lemmy.dbzer0.com
            link
            fedilink
            English
            1
            edit-2
            7 months ago

            A loose FEP wouldn’t cause the print to essentially perfectly skip over multiple layers. Once the FEP finally releases, there would be multiple layers missing, resulting in a very gloppy thick layer, or the remaining layers printing directly on the FEP.

            I can’t think of any situation a loose FEP could result in the above image without at the very least one “extremely large” layer.

            Not to mention, the FEP wouldn’t suddenly tighten, meaning you’d have the same issue over and over.

    • @Tarnaq@lemmy.worldOP
      link
      fedilink
      English
      27 months ago

      I generally have my lift set to 7mm, which should be enough. If it continues even if I don’t pause the print, I’ll give it a try.